Both of these situations will consume lots of current which defeats the purpose of suspend mode. Load… then navigate to your project's bin directory and select the file with the ". Make sure you are using the primary communication jack and cable. This set of simple, almost self explanatory functions control the state and behavior of these LEDs making it easy for your programs to provide the most minimal of visual feedback. If you wish to develop programs that will make use of the Flash, you will need to familiarize yourself with this section in the User's Manual.
| Uploader: | Kakasa |
| Date Added: | 13 September 2013 |
| File Size: | 5.44 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 78943 |
| Price: | Free* [*Free Regsitration Required] |
The other 15 channels are available for your use. Your first program The default C project stationery contains a simple bit of code that prints out the serial number of your CF1 as well as information regarding the program build and the versions of the BIOS and PicoDOS that are burned into your Persistor's flash.
However, it is unlikely that you bought the CF2 solely to write programs with the C Standard Library. If you wish to use another monitor program, set it to: If these are not quite to your liking, you can choose from over two-dozen prewritten functions or even write your own TPU microcode. Contact the factory for application notes.
We did this here with a scope probe tip 0. In addition, in motocroes Docs folder you should see a pdf folder.
The LT has a rated output of mA maximum, but the actual continuous current will vary with temperature and input voltage. It can do almost anything. Make sure the CF2 is not offset in any direction from the connectors. Slocum G1 Glider Manual. Your CF2 Starter Kit should contain the following items: Either or both the receive and transmit drivers can be disabled under software control to conserve power or allow connection to alternate RS or RS drivers.
CF1 Getting Started Guide - Persistor Instruments Inc
The following is a blow-by-blow description of the major hardware subsystems in the CF1. Real Time Clock Drivers - The has an onboard Real Time Clock RTC that has its own precision crystal and its own power lines to allow ultra-reliable operation and persistence through low power shutdowns and hardware reset cycles.
Furthermore, there is a set of macros that provide ultra high-speed access allowing you to perform basic pin operations in under a microsecond with certain restrictions. When your program gets control, you can define this line as a BUS signal for decodingmotocrods input signal though you must not drive into it until you persiistor itor an output signal.
P e r s i s t o r CF8V2 Getting Started Guide |
External circuitry coordinated with CF2 driver software may use this line to pull the CF2 out of suspend persistir.
You use MotoCross to communicate with and load software to the CF2. The CF8V2 will accommodate either type of card.
Product specifications are subject to change without notice. Bo Type B that can operate in open drain mode. Power consumption in a processor varies almost linearly with speed, and we provide functions for you to adjust the system clock anywhere from KHz to 16MHz and beyond. This prompt indicates that the code was loaded into your CF2 and the G which was motkcross sent by MotoCross is an abbreviation for the GO command that will launch your program.
Each SASM can perform one of the following functions: We will choose the name First here as well but the name can be pedsistor from the Target Name.
However, there is motofross K free for non-volatile persistoor storage or data storage if you find the need. It contains the all of the standard ANSI header file includes as well as all of the device specific includes that you will need to work with the CF1.
The LT will allow the CF1 to work with inputs from 3. Do not attempt to assert or load this line. Not all adaptor cables are equal, so if you find one that works well for you then hang on to it!
HydroDAS Firmware Update Procedure
If this is persiator first-time installation, there will likely be only one filename that even comes close. When your program gets control, you can define this line as a BUS signal for decodingan input signal though you must not drive into it until you redefine itor an output signal. This can be a huge time saver if you want your program to be interactive. This is done as a reminder for you to rename the project.
No comments:
Post a Comment